Home Arduino KY-015 Temperature and Humidity Sensor Module

KY-015 Temperature and Humidity Sensor Module

by iainhendry

The KY-015 Temperature and Humidity Sensor Module is based on the DHT11

DHT11 digital temperature and humidity sensor is a composite Sensor contains a calibrated digital signal output of the temperature and humidity. Application of a dedicated digital modules collection technology and the temperature and humidity sensing technology, to ensure that the product has high reliability and excellent long-term stability.

The sensor includes a resistive sense of wet components and an NTC temperature measurement devices, and connected with a high-performance 8-bit microcontroller.

Relative humidity
Resolution: 16Bit
Repeatability: ±1% RH
Accuracy: At 25℃ ±5% RH
Interchangeability: fully interchangeable
Response time: 1 / e (63%) of 25℃ 6s
1m / s air 6s
Hysteresis: <± 0.3% RH
Long-term stability: <± 0.5% RH / yr in

Temperature
Resolution: 16Bit
Repeatability: ±0.2℃
Range: At 25℃ ±2℃
Response time: 1 / e (63%) 10S

Electrical Characteristics
Power supply: DC 3.5~5.5V
Supply Current: measurement 0.3mA standby 60μ A
Sampling period: more than 2 seconds

Connection

Connect the Power line (middle) and ground (-) to +5 and GND respectively. Connect signal (S) to pin A0 on the Arduino.

KY-015 Arduino
S Pin A0
middle +5V
GND

 

Code

[codesyntax lang=”cpp”]


#define dht_dpin A0
byte bGlobalErr;
byte dht_dat[5];

void setup(){
InitDHT();
Serial.begin(9600);
delay(300);
Serial.println("Humidity and temperature\n\n");
delay(700);
}

void loop(){
 ReadDHT();
 switch (bGlobalErr){
 case 0:
 Serial.print("Current humdity = ");
 Serial.print(dht_dat[0], DEC);
 Serial.print(".");
 Serial.print(dht_dat[1], DEC);
 Serial.print("% ");
 Serial.print("temperature = ");
 Serial.print(dht_dat[2], DEC);
 Serial.print(".");
 Serial.print(dht_dat[3], DEC);
 Serial.println("C ");
 break;
 case 1:
 Serial.println("Error 1: DHT start condition 1 not met.");
 break;
 case 2:
 Serial.println("Error 2: DHT start condition 2 not met.");
 break;
 case 3:
 Serial.println("Error 3: DHT checksum error.");
 break;
 default:
 Serial.println("Error: Unrecognized code encountered.");
 break;
 }
 delay(800);
}

void InitDHT(){
 pinMode(dht_dpin,OUTPUT);
 digitalWrite(dht_dpin,HIGH);
}

void ReadDHT(){
bGlobalErr=0;
byte dht_in;
byte i;
digitalWrite(dht_dpin,LOW);
delay(20);

digitalWrite(dht_dpin,HIGH);
delayMicroseconds(40);
pinMode(dht_dpin,INPUT);
//delayMicroseconds(40);
dht_in=digitalRead(dht_dpin);

if(dht_in){
 bGlobalErr=1;
 return;
 }
delayMicroseconds(80);
dht_in=digitalRead(dht_dpin);

if(!dht_in){
 bGlobalErr=2;
 return;
 }
delayMicroseconds(80);
for (i=0; i<5; i++)
 dht_dat[i] = read_dht_dat();
pinMode(dht_dpin,OUTPUT);
digitalWrite(dht_dpin,HIGH);
byte dht_check_sum =
 dht_dat[0]+dht_dat[1]+dht_dat[2]+dht_dat[3];
if(dht_dat[4]!= dht_check_sum)
 {bGlobalErr=3;}
};

byte read_dht_dat(){
 byte i = 0;
 byte result=0;
 for(i=0; i< 8; i++){
 while(digitalRead(dht_dpin)==LOW);
 delayMicroseconds(30);
 if (digitalRead(dht_dpin)==HIGH)
 result |=(1<<(7-i));
 while (digitalRead(dht_dpin)==HIGH);
 }
 return result;
}



[/codesyntax]

Links

37 in 1 box Sensor Kit For Arduino Starters brand in stock

You may also like

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More